So I recently discovered that I have no bracelets. Well, except for the power beads left over from the second grade. Since then, I have been trying to build a collection of bracelets that won’t make me look like a 10 year old. As I was flipping through an InStyle the other day, I came across a bangle wrapped in colored twine and thought, “I can do something like that!” And such brought about the creation of this bracelet I am about to share with you! It’s a little tedious & time consuming, so be patient!
First you will need:
1 bangle-stye bracelet, or I used a plastic ring a scarf came on. You can be ingenuitive and resourceful with this. Just make sure it’s a little big, because the thread will make it a little smaller than it orignally was.
1 spool of thin white embroidery thread (technically it’s called Bedspread Cotton), or you can use regular embroidery thread, in which case I would suggest 2 skeins.
4 skeins (I guess that’s what you call them?) of embroidery thread, each in a different color.
You can find all of these things at Hobby Lobby, or maybe Wal-Mart.
1) To begin, cut about 3 yards of the beadspread cotton. Yes, 3 yards. You will need more than you think, and it’s better to have too much than not enough!
2) Tie one end of the bedspread cotton around the bracelet, leaving as small a tail as possible.
4) Continue wrapping the thread around the bracelet, using your fingernail to make sure it is very tight!
7) Wrap the thread around the loop twice and pull tight. This might not seem like a sturdy knot, but if the wrapping is tight enough, it will be ok! Cut off the end to make a short tail.
8) Next is the colored embroidery thread. I chose to do blue next, but you can do whatever color you like. It is a good idea to leave the thread in its skein form while you’re working with it so it will be easy to pass under the bracelet & won’t get tangled up.
10) We will be doing stripes with this color. Wrap the thread around, leaving spaces inbetween. To achieve straight lines, slant the thread when you bring it around the back of the bracelet.
11) Continue wrapping in this manner until you reach your starting point. Wrap the thread around tightly a few times, and then loosely once, tying a knot as you did in step 7.
12) Now onto orange! To begin, unravel the entire skein of orange thread. Yes, this may seem frightening, and I promise, you WILL have knots. But remember, I told you this project was tedious and required patience :). String the bracelet onto the thread and make a loop around the bracelet in the very middle of the thread, centering the thread in the thick blue section on the bracelet.
13) Next, take the thread and cross it over itself on top of the bracelet. Then cross it again underneath the bracelet. Repeat a few times until you have a thick band of orange.
14) Now, take the thread from each side and cross them a little ways down from the thick band into an X.
15) Then, take the thread and cross it into an X on the back of the bracelet.
16) Continue crossing the thread in the front and then back until you reach your starting point. A tip is to hold the bracelet between your knees so your hands will be free to work!
17) When you get to the orange band, you may have to do an odd-shaped X to make it fit, since the thread needs to be underneath the bracelet. My X was a little squatty, but it’s ok!
18) Wrap the thread around a few times, then tie the easiest knot of the bracelet! Just cross the thread under and pull tight, like the first step of tying your shoes! Then cut the ends off, remembering to leave short tails.
20) Then, wrap the yellow diagonally between the orange X’s, making sure you’re wrapping very tightly!
21) When you reach your starting point, you can cut it off if you want, but I continued wrapping twice more to add a thick yellow line.
22) When you reach your starting point for the third time, tie a knot like you did for the blue and the white.
This is what you have so far!
23) And now for the green! Tie it on and wrap it around to hide the tails.